MBONED Working Group                               Dorian Kim
Internet Draft                                     Verio
                                                   David Meyer
                                                   Cisco Systems
                                                   Henry Kilmer
                                                   Dino Farinacci
                                                   Procket Networks
Category                                           Experimental
                                                   May, 2001

                Anycast RP mechanism using PIM and MSDP

1. Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC 2026.

   Internet Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at

   The list of Internet-Draft Shadow Directories can be accessed at

2. Abstract

   This document describes a mechanism to allow for an arbitrary number
   of RPs per group in a single shared-tree PIM-SM domain.

   This memo is a product of the MBONE Deployment Working Group (MBONED)
   in the Operations and Management Area of the Internet Engineering
   Task Force. Submit comments to <mboned@ns.uoregon.edu> or the

3. Copyright Notice

   Copyright (C) The Internet Society (2000). (2001).  All Rights Reserved.

4. Introduction

   PIM-SM as defined in RFC 2362 allows for only a single active RP per
   group, and as such the decision of optimal RP placement can become
   problematic for a multi-regional network deploying PIM-SM.

   Anycast RP relaxes an important constraint in PIM-SM, namely, that
   there can be only one group to RP mapping can be active at any time.
   The single mapping property has several implications, including
   traffic concentration, lack of scalable register decapsulation (when
   using the shared tree), slow convergence when an active RP fails,
   possible  sub-optimal forwarding of multicast packets, and distant RP
   dependencies. These properties of PIM-SM have been demonstrated in
   native continental or inter-continental scale multicast deployments.
   As a result, it is clear that ISP backbones require a mechanism that
   allows definition of multiple active RPs per group in single PIM-SM
   domain. Further, any such mechanism should also address the issues
   addressed above.

   The mechanism described here is intended to address the need for
   better fail-over (convergence time) and sharing of the register
   decapsulation load (again, when using the shared-tree) among RPs in a
   domain. It is primarily intended for applications within those
   networks which are using MBGP, Multicast Source Discovery Protocol
   [MSDP] and PIM-SM protocols for native multicast deployment, although
   it not limited to those protocols. In particular, Anycast RP is
   applicable in any PIM-SM network that also supports MSDP (MSDP is
   required so that the various RPs in the domain maintain a consistent
   view of the sources that are active). Note however, a domain
   deploying Anycast RP is not required to run MBGP. Finally, a general
   requirement of the Anycast RP scheme is that the anycast address MUST
   NOT be used as the RP address in the RP's SA messages.

   SHALL, SHALL NOT, SHOULD, SHOULD NOT are to be interpreted as defined
   in RFC 2119 [RFC2119].

5. Problem Definition

   The anycast RP solution provides a solution for both fast fail-over
   and shared-tree load balancing among any number of active RPs in a

5.1. Traffic Concentration and Distributing Decapsulation Load Among RPs

   While PIM-SM allows for multiple RPs to be defined for a given group,
   only one group to RP mapping can active at a given time. A
   traditional deployment mechanism for balancing register decapsulation
   load between multiple RPs covering the multicast group space is to
   split up the space between multiple defined RPs. This is
   an acceptable solution as long as multicast traffic remains low, but
   has problems as multicast traffic increases, especially because the
   network operator defining group space split between RPs does not
   always have a priori knowledge of traffic distribution between
   groups. This can be overcome via periodic reconfigurations, but
   operational considerations cause this type of solution to scale

5.2. Sub-optimal Forwarding of Multicast Packets

   When a single RP serves a given multicast group, all joins to that
   group will be sent to that RP regardless of the topological distance
   between the RP and the sources and receivers. Initial data will be
   sent towards the RP also until configured shortest path tree switch
   threshold is reached, or the data will always be sent towards the RP
   if the network is configured to always use RP rooted shared tree.
   This holds true even if all the sources and the receivers are in any
   given single region, and RP is topologically distant from the sources
   and the receivers. This is an artifact of the dynamic nature of
   multicast group members, and of the fact that operators may not
   always have a priori knowledge of the topological placement of the
   group members.

   Taken together, these effects can mean that (for example) although
   all the sources and receivers of a given group are in Europe, they
   are joining towards the RP in USA and the data will be traversing
   relatively expensive pipe(s) twice, once to get to RP, and back down
   the RP rooted tree again, creating inefficient use of expensive

5.3. Distant RP Dependencies

   As outlined above, a single active RP per group may cause local
   sources and receivers to become dependent on a topologically distant
   RP. In addition, when multiple RPs are configured, there can be
   considerable convergence delay involved in switching to the backup
   RP. This delay may exist independent of the toplogical location of
   the primary and backup RPs.

6. Solution

   Given the problem set outlined above, a good solution would allow an
   operator to configure multiple RPs per group, and distribute those
   RPs in a topologically significant manner to the sources and

6.1. Mechanisms

   All the RPs serving a given group or set of groups are configured
   with identical anycast address, using a numbered interface on the RPs
   (frequently a logical interface such as a loopback is used). RPs then
   advertise group to RP mappings using this interface address. This
   will cause group members (senders) to join (register) towards the
   topologically closest RP. RPs MSDP peer with each other using an
   address unique to each RP. Since the anycast address is not a unique
   address (by definition), a router MUST NOT choose the anycast unicast
   address as the router ID as this can prevent peerings and/or
   adjacencies from being established.

   In summary then, the following steps are required:

6.1.1. Create the set of group-to-anycast-RP-address mappings

   The first step is to create the set of group-to-anycast-RP-address
   mappings to be used in the domain. Each RP participating in a anycast
   RP set must be configured with a consistent set of group to RP
   address mappings. This mapping will be used by the non-RP routers in
   the domain.

6.1.2. Configure each RP for the group range with the anycast RP address

   The next step is to configure each RP for the group range with the
   anycast RP address. If a dynamic mechanism such as auto-RP or the
   PIMv2 bootstrap mechanism is being used to advertise group to RP
   mappings, the anycast IP address should be used for the RP address.

6.1.3. Configure MSDP peerings between each of the anycast RPs in the

   Unlike the group to RP mapping advertisements, MSDP peerings must use
   an IP address that is unique to the endpoints; that is, the MSDP
   peering endpoints MUST use a unicast rather than anycast address. A
   general guideline is to follow the addressing of the BGP peerings,
   e.g., loopbacks for iBGP peering, physical interface addresses for
   eBGP peering. Note that the anycast address MUST NOT be used as the
   RP address in SA messages (as this would case the peer-RPF check to

6.1.4. Configure the non-RP's with the group-to-anycast-RP-address

   Finally, each non-RP router must learn the set of group to RP
   mappings. This could be done via static configuration, auto-RP, or by
   PIMv2 bootstrap mechanism.

6.1.5. Ensure that the anycast IP address is reachable by all routers in
   the domain

   This is typically accomplished by causing each RP to inject the /32
   into the domain's IGP.

6.2. Interaction with MSDP Peer-RPF check

   Each MSDP peer receives and forwards the message away from the RP
   address in a "peer-RPF flooding" fashion.  The notion of peer-RPF
   flooding is with respect to forwarding SA messages [MSDP]. The BGP
   routing tables are examined to determine which peer is the next hop
   towards the originating RP of the SA message.  Such a peer is called
   an "RPF peer".  See [MSDP] for details of the Peer-RPF check.

6.3. State Implications

   It should be noted that using MSDP in this way forces the creation of
   (S,G) state along the path from the receiver to the source. This
   state may not be present if a single RP was used and receivers were
   forced to stay on the shared tree.

7. Security considerations

   Since the solution described here makes heavy use of anycast
   addressing, care must be taken to avoid spoofing. In particular
   unicast routing and PIM RPs must be protected.

7.1. Unicast Routing

   Both internal and external unicast routing can be weakly protected
   with keyed MD5 [RFC1828], as implemented in an internal protocol such
   as OSPF [RFC2382] or in BGP [RFC2385]. More generally,  IPSEC
   [RFC1825] could be used to provide protocol integrity for the unicast
   routing system.

7.1.1. Effects of Unicast Routing Instability

   While not a security issue, it is worth noting that if unicast
   routing is unstable, then the actual RP that source or receiver is
   using will be subject to the same instability.

7.2. Multicast Protocol Integrity

   The mechanisms described in [RFC2362] should be used to provide
   protocol message integrity protection and group-wise message origin

7.3. MSDP Peer Integrity

   As is the the case for BGP, MSDP peers can be protected using keyed
   MD5 [RFC1828].

8. Acknowledgments

   John Meylor, Bill Fenner, Dave Thaler and Tom Pusateri provided
   insightful comments on earlier versions for this idea.

9. Author's Address

   Dorian Kim
   Verio, Inc.
   2361 Lancashire Dr. #2A
   Ann Arbor, MI 48015
   Email: dorian@blackrose.org

   Hank Kilmer
   Email: hank@rem.com

   Dino Farinacci
   Procket Networks
   Email: dino@procket.com

   David Meyer
   Email: dmm@maoz.com

10. References

   [MSDP]     D. Farinacci, et. al., Meyer and B. Fenner, Editors, "Multicast Source Discovery
              Protocol (MSDP)", draft-ietf-msdp-spec-02.txt,
              January, 2000. draft-ietf-msdp-spec-10.txt,
              May, 2001.  Work in Progress.

   [RFC1825]  Atkinson, R., "IP Security Architecture", August 1995.

   [RFC1828]  P. Metzger and W. Simpson, "IP Authentication using Keyed
              MD5", RFC 1828, August, 1995.

   [RFC2119]   S. Bradner, "Key words for use in RFCs to Indicate
               Requirement Levels", RFC 2119, March, 1997.

   [RFC2362]  D. Estrin, et. al., "Protocol Independent Multicast-
              Sparse Mode (PIM-SM): Protocol Specification", RFC
              2362, June, 1998.

   [RFC2382]  Moy, J., "OSPF Version 2", RFC 2382, April 1998.

   [RFC2385]  Herrernan, A., "Protection of BGP Sessions via the TCP
              MD5 Signature Option", RFC 2385, August, 1998.

   [RFC2403]  C. Madson and R. Glenn, "The Use of HMAC-MD5-96 within
              ESP and AH", RFC 2403, November, 1998.

10. Author's Address

   Dorian Kim
   Verio, Inc.
   2361 Lancashire Dr. #2A
   Ann Arbor, MI 48015
   Email: dorian@blackrose.org

   Hank Kilmer
   Email: hank@rem.com

   Dino Farinacci
   Procket Networks
   Email: dino@procket.com

   David Meyer
   Cisco Systems, Inc.
   170 Tasman Drive
   San Jose, CA, 95134
   Email: dmm@cisco.com

11. Full Copyright Statement

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an