Mobile Ad Hoc Networking Working Group                Charles E. Perkins
INTERNET DRAFT                             Sun Microsystems Laboratories
25 June                                     Nokia Research Center
22 October 1999                                       Elizabeth M. Royer
                                 University of California, Santa Barbara
                                                            Samir R. Das
                                        University of Texas, San Antonio

             Ad Hoc On-Demand Distance Vector (AODV) Routing
                      draft-ietf-manet-aodv-03.txt
                      draft-ietf-manet-aodv-04.txt

Status of This Memo

   This document is a submission by the Mobile Ad Hoc Networking Working
   Group of the Internet Engineering Task Force (IETF).  Comments should
   be submitted to the manet@itd.nrl.navy.mil mailing list.

   Distribution of this memo is unlimited.

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.  Internet-Drafts are working
   documents of the Internet Engineering Task Force (IETF), its areas,
   and its working groups.  Note that other groups may also distribute
   working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at
   any time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at:
        http://www.ietf.org/ietf/1id-abstracts.txt
   The list of Internet-Draft Shadow Directories can be accessed at:
        http://www.ietf.org/shadow.html.

Abstract

   The Ad Hoc On-Demand Distance Vector (AODV) routing protocol is
   intended for use by mobile nodes in an ad hoc network.  It offers
   quick adaptation to dynamic link conditions, low processing and
   memory overhead, low network utilization, and establishment of determines both unicast
   and multicast routes between sources and destinations.  It uses
   destination sequence numbers to ensure loop freedom at all times
   (even in the face of anomalous delivery of routing control messages),
   solving problems (such as ``counting to infinity'') associated with
   classical distance vector protocols.

                                Contents

Status of This Memo                                                    i

Abstract                                                               i

 1. Introduction                                                       1

 2. Overview                                                           2

 3. AODV Terminology                                                   4

 4. Route Request (RREQ) Message Format                                6

 5. Route Reply (RREP) Message Format                                  7                                  8

 6. Route Error (RERR) Message Format                                  9

 7. Multicast Activation (MACT) Message Format                        10

 8. Group Hello (GRPH) Message Format                                 11

 9. Node Operation - Unicast                                           8
     6.1.                                          12
     9.1. Maintaining Route Utilization Records . . . . . . . . . .    8
     6.2. Maintaining Associations between Services and IP Addresses   9
     6.3.   12
     9.2. Generating Route Requests (RREQs) . . . . . . . . . . . .    9
           6.3.1. . . . .   13
           9.2.1. Controlling RREQ broadcasts Route Request Broadcasts  . . . . . .   13
     9.3. Forwarding Route Requests . . . . .   10
     6.4. Forwarding RREQs . . . . . . . . . . .   14
           9.3.1. Processing Route Requests . . . . . . . . .   10
           6.4.1. Handling Route Requests (RREQs) for IP
                          Destinations . . .   15
     9.4. Generating Route Replies  . . . . . . . . . . . .  11
           6.4.2. Handling Route Requests (RREQs) for Services . .   11
     6.5. Generating Route Replies (RREPs) for IP Destinations . .   12
     6.6. Generating   15
     9.5. Forwarding Route Replies (RREPs) for Services  . . . . . .   12
     6.7. . . . . . . . . . .   16
     9.6. Hello Messages  . . . . . . . . . . . . . . . . . . . . .   13
     6.8.   17
     9.7. Maintaining Local Connectivity  . . . . . . . . . . . . .   14
     6.9. Initiating Triggered   18
     9.8. Route Replies (Triggered RREPs) Error (RERR) Messages . .   14

 7. Multicast Route Activation (MACT) Message Format                  15

 8. . . . . . . . . . . . . .   19

10. Node Operation - Multicast                                        16
     8.1.                                        19
    10.1. Maintaining Multicast Tree Utilization Records  . . . . .   16
     8.2.   20
    10.2. Generating Multicast RREQs Route Requests . . . . . . . . . . . . . . .   17
     8.3. .   20
    10.3. Forwarding Multicast Route Requests . . . . . . . . . . .   17
     8.4. . . . . .   21
    10.4. Generating Multicast Route Replies  . . . . . . . . . . .   18
     8.5. . . . . .   21
    10.5. Forwarding Route Replies  . . . . . . . . . . . . . . . .   19
     8.6.   22
    10.6. Route Deletion and Multicast Tree Pruning Activation  . . . . . . . .   19
     8.7. Repairing Link Breakages . . . . . . . . . . . .   23
    10.7. Multicast Tree Pruning  . . . . . .   20
     8.8. Initiating Triggered Route Replies . . . . . . . . . . .   23

 9. Broadcast                                                         23

10. Quality of Service                                                24

11. AODV and Aggregated Networks   24

12. Using AODV with Other Networks                                    25

13. Service Location with AODV                                        25

14. Extensions                                                        26
    14.1. Hello Interval Extension Format
    10.8. Repairing Link Breakages  . . . . . . . . . . . . .   26
    14.2. Multicast Group Leader Extension Format . . .   24
    10.9. Tree Partitions . . . . . .   27
    14.3. Multicast Group Information Extension Format . . . . . .   27
    14.4. Maximum Delay Extension Format . . . . . . . . .   26
   10.10. Reconnecting the Two Trees  . . . .   29
    14.5. Minimum Bandwidth Extension Format . . . . . . . . . . .   29
    14.6. Service Resolution Extension Format   27
   10.11. Group Hello Messages  . . . . . . . . . . . . . . . . . .   28

11. Broadcast                                                         29

12. Quality of Service                                                29

13. AODV and Aggregated Networks                                      30

15. Configuration Parameters

14. Using AODV with Other Networks                                    30

15. Extensions                                                        31
    15.1. Hello Interval Extension Format . . . . . . . . . . . . .   32
    15.2. Multicast Group Leader Extension Format . . . . . . . . .   32
    15.3. Multicast Group Rebuild Extension Format  . . . . . . . .   33
    15.4. Multicast Group Information Extension Format  . . . . . .   34
    15.5. Maximum Delay Extension Format  . . . . . . . . . . . . .   34
    15.6. Minimum Bandwidth Extension Format  . . . . . . . . . . .   35

16. Configuration Parameters                                          36

17. Security Considerations                                           31                                           37

1. Introduction

   The Ad Hoc On-Demand Distance Vector (AODV) algorithm enables
   dynamic, self-starting, multihop routing between participating mobile
   nodes wishing to establish and maintain an ad hoc network.  AODV
   allows mobile nodes to obtain routes quickly for new destinations,
   and does not require nodes to maintain routes to destinations that
   are not in active communication.  Additionally, AODV allows for the
   formation of multicast groups whose membership is free to change
   during the lifetime of the network.  AODV allows mobile nodes to
   respond quickly to link breakages and changes in network topology.
   The operation of AODV is loop-free, and by avoiding the Bellman-Ford
   ``counting to infinity'' problem offers quick convergence when the
   ad hoc network topology changes (typically, when a node moves in the
   network).

   One distinguishing feature of AODV is its use of a destination
   sequence number for each route entry.  The destination sequence
   number is created by the destination or the multicast group leader
   for any usable route information it sends to requesting nodes.  Using
   destination sequence numbers ensures loop freedom and is simple to
   program.  Given the choice between two routes to a destination, a
   requesting node always selects the one with the greatest sequence
   number.

   Another feature of AODV is that link breakages cause immediate
   notifications to be sent to the affected set of nodes, but only that
   set of nodes.

2. Overview

   Route Requests (RREQs), Route Replies (RREPs), and Multicast Route Errors (RERRs),
   Multicast Activations (MACTs) (MACTs), and Group Hellos (GRPHs) are the three
   message types defined by AODV. These message types are handled by
   UDP, and normal IP header processing applies.  So, for instance, the
   requesting node is expected to use its IP address as the source IP
   address for the messages.  The range of dissemination of broadcast
   RREQs can be indicated by the TTL in the IP header.  Fragmentation is
   typically not required.

   As long as the endpoints of a communication connection have valid
   routes to each other, AODV does not play any role.  When a route
   to a new destination (either a single node or a multicast group)
   is needed, the node uses a broadcast RREQ to find a route to the
   destination.  A route can be determined when the RREQ reaches either
   the destination itself, or an intermediate node with a 'fresh `fresh enough'
   route to the destination.  A 'fresh `fresh enough' route is an unexpired
   route entry for the destination whose associated sequence number is
   at least as great as that contained in the RREQ. The route is made
   available by unicasting a RREP back to the source of the RREQ. Since
   each node receiving the request caches a route back to the source of
   the request, the RREP can be unicast back from the destination to
   the source, or from any intermediate node that is able to satisfy
   the request back to the source.  A RREQ can be conditioned by
   requirements on the path to the destination, namely bandwidth or
   delay bounds.  A RREQ can also be

   Nodes monitor the link status of next hops in active routes.  When a
   link break in an active route is detected, a RERR message is used to access specific service
   entities and at
   notify other nodes that the same time discover loss of that link has occured.  The RERR
   message indicates which destinations are now unreachable due to the IP address
   loss of the desired
   service. link.

   RREQs are also used when a node wishes to join a multicast group.
   A join flag in the RREQ informs nodes that when receiving the
   RREP, they are not just setting route pointers but are also setting
   multicast route pointers, which will be used if the route is selected
   to be added onto the tree.  If the route is chosen for addition to
   the multicast tree, it will be activated by a MACT message.

   For multicast groups, a Group Hello message is periodically broadcast
   across the network by the multicast group leader.  The message
   carries multicast group and corresponding group leader IP addresses.
   This information is used for repairing multicast trees after a
   previously disconnected portion of the network containing part of the
   multicast tree becomes reachable once again.

   Since AODV is a routing protocol, it deals with route table
   management.  Route table information must be kept even for ephemeral
   routes, such as are created to temporarily store reverse paths
   towards nodes originating RREQs.  AODV uses the following fields with
   each route table entry:

    -  Destination IP Address

    -  Destination Sequence Number

    -  Hop Count (number of hops needed to reach destination)

    -  Last Hop Count (described in subsection 6.3.1) 9.2.1)

    -  Next Hop

    -  List of Precursors (described in Section 6.1) 9.1)

    -  Lifetime (expiration time of the route)
    -  Routing Flags

   The following information is stored in each entry of the multicast
   route table for multicast tree routes:

    -  Multicast Group IP Address

    -  Multicast Group Leader IP Address

    -  Multicast Group Sequence Number

    -  Next Hops

    -  Hop Count to next Multicast Group member Member

    -  Hop Count to Multicast Group leader

       -  Next Hops
       -  Lifetime Leader

   The Next Hops field is a linked list of structures, each of which
   contains the following fields:

    -  Next Hop IP address of a neighbor in the multicast tree Address

    -  Link Direction of the link

    -  Enabled  Activated Flag

   The direction of the link is relative to the location of the group
   leader, i.e.  UPSTREAM is a next hop towards the group leader, and
   DOWNSTREAM is a next hop away from the group leader.  A node on
   the multicast tree must necessarily have only one UPSTREAM link.
   The IP Address of a Next Hop MUST NOT be used to forward multicast
   messages until after a MACT message has enabled activated the route (see
   Section 8.6).

   In order to assist applications in resolving IP addresses 10.6).

3. AODV Terminology

   This protocol specification uses conventional meanings [1] for their
   service needs, each node maintains a list of associations between
   service types and IP addresses.  If no IP address is known for a
   service, then the RREQ message can be used with the `S' bit set to
   find such an IP address.  If an IP address is known for a service,
   but no path is known for the IP address, then the RREQ message
   with the `S' bit reset is used as before to find a path to the IP
   destination address.  The association between a service type and IP
   address expires after SERVICE_ADDR_TIMEOUT milliseconds.  If the
   service is still needed, the association must be re-established by
   issuing another RREQ.

3. AODV Terminology

   This protocol specification uses conventional meanings [1] for
   capitalized words such as MUST, SHOULD, etc., to indicate requirement
   levels
   capitalized words such as MUST, SHOULD, etc., to indicate requirement
   levels for various protocol features.  This section defines other
   terminology used with AODV that is not already defined in [2].

      active route

         A routing table entry with an unexpired Lifetime and a finite
         metric in the Hop Count field.  A routing table may contain
         entries that are not active.  Only active entries can be used
         to forward data packets.

      forwarding node

         A node which agrees to forward packets destined for another
         destination node, by retransmitting them to a next hop which is
         closer to the unicast destination along a path which has been
         set up using routing control messages.

      group leader

         A node which is a member of the given multicast group
         and which is typically the first such group member in the
         connected portion of the network.  This node is responsible for
         initializing and maintaining the multicast group destination
         sequence number.

      group leader table

         The table where ad hoc nodes keep information concerning each
         multicast group and its corresponding group leader.  There is
         one entry in the table for each multicast group for which the
         node has received a Group Hello (see Section 8.2). 10.2).

      multicast tree

         The tree containing all nodes which are members of the
         multicast group and all nodes which are needed to connect the
         multicast group members.

      multicast route table

         The table where ad hoc nodes keep routing (including next hops)
         information for various multicast groups.

      subnet leader

         A node which is a member of the subnet defined by a specific
         routing prefix, and which offers reachability to every other
         node with the same routing prefix.  The subnet leader is
         responsible for initializing and maintaining the destination
         sequence number for every node on the subnet.

4. Route Request (RREQ) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |J|R|S|      |J|R|        Reserved           |   Hop Count   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                          Broadcast ID                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Destination IP address                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Destination Sequence Number                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Source IP address                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Source Sequence Number                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The format of the Route Request message is illustrated above, and
   contains the following fields:

      Type           1

      J              Join flag; set when source node wants to join a
                     multicast group.

      R              Repair flag; set when a node wants to initiate
                     a repair to connect two previously disconnected
                     portions of the multicast tree.

      S              Service Location; set when a node wants to discover
                     a service rather than a particular IP address.

      Reserved       Sent as 0; ignored on reception.

      Hop Count      The number of hops from the Source IP Address to
                     the node handling the request.

      Broadcast ID   A sequence number uniquely identifying the
                     particular RREQ when taken in conjunction with the
                     source node's IP address.

      Destination IP Address
                     The IP address of the service or destination for which a route is
                     desired.  If the `S' bit is zero,
                     this address is an IP address.  If the `S' bit
                     is set, the first 16 bits of the address is the
                     Protocol number and the last 16 bits of the address
                     is the Port number for the desired service (see
                     section 13).

      Destination Sequence Number
                     The last sequence number received in the past by
                     the source for any route towards the destination.

      Source IP Address
                     The IP address of the node which originated the
                     Route Request.

      Source Sequence Number
                     The current sequence number to be used for route
                     entries pointing to (and generated by) the source
                     of the route request.

   When a node wishes to repair a multicast tree, it appends the
   Multicast Group Leader Rebuild extension (see Section 14.2). 15.3).  When a node
   wishes to discover a route to a server unicast the RREQ for a particular application,
   instead of discovering a route multicast group to an IP address, the node sets the
   Protocol and Port number into the Destination Address field, sets the
   `S' bit, and takes group leader,
   it includes the actions specified in Multicast Group Leader extension (see Section 13. 15.2).

5. Route Reply (RREP) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |R|U|      |R|      Reserved     | Prefix Size  |   Hop Count   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Destination IP address                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Destination Sequence Number                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Source IP address                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                           Lifetime                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The format of the Route Reply message is illustrated above, and
   contains the following fields:

      Type          2

      R             Repair flag; set when a node is responding
                    to a repair request to connect two previously
                    disconnected portions of the multicast tree.

      U             Update flag; set in a Group Hello, when the group
                    leader information has changed.

      Reserved      Sent as 0; ignored on reception.

      Prefix Size        If nonzero, the Prefix Size specifies that the
                    indicated next hop may be used for any nodes with
                    the same routing prefix (as defined by the Prefix
                    Size) as the requested destination.

      Hop Count     The number of hops from the Source IP Address to
                    the Destination IP Address.  For multicast route
                    requests this indicates the number of hops to the
                    multicast tree member sending the RREP.

      Destination IP Address
                    The IP address of the destination for which a route
                    is supplied.

      Destination Sequence Number
                    The destination sequence number associated to the
                    route.

      Source IP Address
                    The IP address of the source node which issued the
                    RREQ for which the route is supplied.

      Lifetime      The time for which nodes receiving the RREP consider
                    the route to be valid.

   When the RREP is sent for a multicast destination, the Multicast
   Group Information extension is appended (see Section 14.3). 15.4).

   Note that the Prefix Size allows a Subnet Leader to supply a route
   for every host in the subnet defined by the routing prefix, which
   is determined by the IP address of the Subnet Leader and the Prefix
   Size.  In order to make use of this feature, the Subnet Leader has to
   guarantee reachability to all the hosts sharing the indicated subnet
   prefix.  The Subnet Leader is also responsible for maintaining the
   Destination Sequence Number for the whole subnet.

6. Node Operation - Unicast

   This section describes the scenarios under which nodes generate
   RREQs and RREPs for unicast communication, and how the fields in the
   message Route Error (RERR) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |           Reserved            |    Length     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Unreachable Destination IP Address (1)             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Additional Unreachable Destination IP Addresses (if needed...) |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The format of the Route Error message is illustrated above, and
   contains the following fields:

      Type     3

      Reserved Sent as 0; ignored on reception.

      Length   The number of unreachable destinations included in the
               message.  Must be at least 1.

      Unreachable Destination IP Address
               The IP address of the destination which has become
               unreachable due to a link break.

   The RERR message is sent whenever a link break causes one or more
   destinations to become unreachable.  The unreachable destination
   addresses included are those of all lost destinations which are now
   unreachable due to the loss of that link.

7. Multicast Activation (MACT) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |P|G|U|      Reserved           |   Hop Count   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Multicast Group IP address                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Source IP address                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Source Sequence Number                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The format of the Multicast Activation message is illustrated above,
   and contains the following fields:

      Type        4

      P           Prune flag; set when a node wishes to prune itself
                  from the tree, unset when the node is activating a
                  tree link.

      G           Group Leader flag; set by a multicast tree member that
                  fails to repair a multicast tree link breakage, and
                  indicates to the group member receiving the message
                  that it should become the new multicast group leader.

      U           Update flag; set when a multicast tree member has
                  repaired a broken tree link and is now a new distance
                  from the group leader.

      Reserved    Sent as 0; ignored on reception.

      Hop Count   The distance of the sending node from the multicast
                  group leader.  Used only when the `U' flag is set;
                  otherwise sent as 0.

      Multicast Group IP Address
                  The IP address of the Multicast Group for which a
                  route is supplied.

      Source IP Address
                  The IP address of the sending node.

      Source Sequence Number
                  The current sequence number for route information
                  generated by the source of the route request.

   To prune itself from the tree (i.e., inactivate its last link to the
   multicast tree), a multicast tree member sends a MACT with the `P'
   flag = 1 to its next hop on the multicast tree.  A multicast tree
   member that has more than one next hop to the multicast tree SHOULD
   NOT prune itself from the multicast tree.

8. Group Hello (GRPH) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |U|M|       Reserved            |   Hop Count   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Group Leader IP address                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Multicast Group IP address                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Multicast Group Sequence Number                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   The format of the Group Hello message is illustrated above, and
   contains the following fields:

      Type        5

      U           Update flag; set when there has been a change in group
                  leader information.

      M           Off_Mtree flag; set by a node receiving the group
                  hello that is not on the multicast tree.

      Reserved    Sent as 0; ignored on reception.

      Hop Count   The number of hops the packet has traveled.  Used by
                  multicast tree nodes to update their distance from the
                  group leader when the M flag is not set.

      Group Leader IP Address
                  The IP address of the group leader.

      Multicast Group IP Address
                  The IP address of the Multicast Group for which the
                  sequence number is supplied.

      Multicast Group Sequence Number
                  The current sequence number of the multicast group.

9. Node Operation - Unicast

   This section describes the scenarios under which nodes generate
   RREQs and RREPs for unicast communication, and how the fields in the
   message are handled.

6.1.

9.1. Maintaining Route Utilization Records

   For each valid route maintained by a node (containing a finite Hop
   Count metric) as a routing table entry, the node also maintains a
   list of precursors that may be forwarding packets on this route.
   These precursors will receive notifications from the node in the
   event of detection of the loss of the next hop link.  The list of
   precursors in a routing table entry contains those neighboring nodes
   to which a route reply was generated or forwarded.

   Each time a route is used to forward a data packet, its Lifetime
   field is updated to be current time plus ACTIVE_ROUTE_TIMEOUT.

6.2. Maintaining Associations between Services and IP Addresses

   Whenever a node needs to contact a server for a particular service
   type, it consults its list of associations between service types and
   IP addresses.  If there is no entry for a server of the desired type,
   the mobile node has to issue a RREQ with the `S' bit set.

   Each entry in the service type table is valid only for
   SERVICE_ADDR_TIMEOUT milliseconds, and MUST be deleted after
   that amount of time.  Since this timeout is much longer than that for
   typical routes to IP destinations, it will often happen that a valid
   association exists between a service type and an IP address, when no
   valid route is available to the associated IP address.

6.3.

9.2. Generating Route Requests (RREQs)

   A node broadcasts a RREQ when it determines that it needs a route to
   a destination (or service) and does not have one available.  This can happen if
   the destination is previously unknown to the node, or if a previously
   valid route to the destination expires or is broken (i.e., an
   infinite metric is associated with the route).  When a route table
   entry is marked with an infinite metric, its Lifetime is also updated
   to be the current time plus BAD_LINK_LIFETIME milliseconds.  After
   the Lifetime expires, the route MAY be expunged from the node's route
   table.

   After broadcasting a RREQ, a node waits for a RREP. If the RREP
   is not received within RREP_WAIT_TIME milliseconds, the node MAY
   rebroadcast the RREQ, up to a maximum of RREQ_RETRIES times.  Each
   rebroadcast MUST increment the Broadcast ID field.

   Data packets waiting for a route (i.e., waiting for a RREP after RREQ
   has been sent) SHOULD be buffered.  The buffering SHOULD be FIFO. If
   a RREQ has been rebroadcast RREQ_RETRIES times without receiving any
   RREP, all data packets destined for the corresponding destination
   SHOULD be dropped from the buffer.

6.3.1.

9.2.1. Controlling RREQ broadcasts Route Request Broadcasts

   To prevent unncessary unnecessary network-wide broadcasts of RREQs, the
   source node SHOULD use an expanding ring search technique as an
   optimization.  In an expanding ring search, the source node initially
   uses a TTL = TTL_START in the RREQ packet IP header and sets the
   timeout for receiving a RREP to 2 * TTL * NODE_TRAVERSAL_TIME
   milliseconds.  Upon timeout, the source rebroadcasts the RREQ with
   the TTL incremented by TTL_INCREMENT. This continues until the
   TTL set in the RREQ reaches TTL_THRESHOLD, beyond which a TTL =
   NET_DIAMETER is used for each rebroadcast.  Each time, the timeout
   for receiving a RREP is calculated as before.  Each rebroadcast
   increments the Broadcast ID field in the RREQ packet.  The RREQ
   can be rebroadcast with TTL = NET_DIAMETER up to a maximum of
   RREQ_RETRIES times.

   When a RREP is received, the Hop Count used in the RREP packet is
   remembered as Last Hop Count in the routing table.  When a new route
   to the same destination is required at a later time (e.g., upon route
   loss), the TTL in the RREQ IP header is initially set to this Last
   Hop Count plus TTL_INCREMENT. Thereafter, following each timeout the
   TTL is incremented by TTL_INCREMENT until TTL = TTL_THRESHOLD is
   reached.  Beyond this TTL = NET_DIAMETER is used as before.

   As a further optimization, timeouts MAY be determined dynamically via
   measurements, instead of using a statically configured value related
   to NODE_TRAVERSAL_TIME. To accomplish this, the RREQ may carry the
   timestamp via an extension field as defined in Section 14 15 to be
   carried back by the RREP packet (again via an extension field).  The
   difference between the current time and this timestamp will determine
   the route discovery latency.  The timeout may be set to be a small
   factor of the average of the last few route discovery latencies
   for the concerned destination.  These latencies may be recorded as
   additional fields in the routing table.

   If the optimizations described in this section are used, an expired
   routing table entry should not be expunged too early.  Otherwise, the
   soft states corresponding to the route (e.g., Last Hop Count) will be
   lost.  In such cases, a longer routing table entry expunge time may
   be specified.  In general, any routing table entry waiting for a RREP
   should not be expunged before the timeout for receiving RREP.

6.4.

9.3. Forwarding RREQs Route Requests

   When a node receives a broadcast RREQ, it first checks to see
   whether it has received a RREQ with the same Source IP Address and a
   Broadcast ID field of equal unsigned integer value within the last
   BCAST_ID_SAVE milliseconds.  If such a RREQ has been received, the
   node silently discards the newly received RREQ. The rest of this
   subsection describes actions taken for RREQs that are not discarded.

6.4.1. Handling

9.3.1. Processing Route Requests (RREQs) for IP Destinations

   If the `S' bit is not set,

   When a node receives a RREQ, the node checks to see whether it has
   a route to the destination.  If the node does not have a route,
   it rebroadcasts the RREQ from its interface(s) but using its own
   IP address in the IP header of the outgoing RREQ. The TTL or hop
   limit field in the outgoing IP header is decreased by one.  The Hop
   Count field in the broadcast RREQ message is incremented by one, to
   account for the new hop through the intermediate node.  The node
   also creates or updates a reverse route to the Source IP Address
   in its routing table with next hop equal to the IP address of the
   neighboring node that sent the broadcast RREQ (often not equal to the
   Source IP Address field in the RREQ message).  This reverse route
   might be used for an eventual RREP back to the node which originated
   the RREQ (identified by the Source IP Address).  If no route exists
   for the Source IP Address, or if an existing route will expire too
   soon, the reverse route is put into the route table with lifetime
   REV_ROUTE_LIFE milliseconds.

   If, on the other hand, the node does have the requested route, it
   compares the destination sequence number (dest-seqno) for that route
   with the Destination Sequence Number field of the incoming RREQ.
   If the node's existing dest-seqno is smaller than the Destination
   Sequence Number field of the RREQ, the node again rebroadcasts the
   RREQ just as if it did not have a route to the destination at all.

   If the node has a route to the destination, and the node's existing
   dest-seqno is greater than or equal to the Destination Sequence
   Number of the RREQ, then the node generates a RREP as discussed
   further in section 6.5.

6.4.2. Handling Route Requests (RREQs) for Services

   If the `S' bit is set in the RREQ message header, and if a node can
   resolve the service type indicated by the requested in the RREQ,
   and if the node has a valid route to the resolved IP address for
   the service type, then the node can generate a RREP as specified
   in section 6.6.  Otherwise, if the node has already rebroadcast a
   RREQ with the same Broadcast ID from the same source node, it MUST
   silently discard the RREQ. Otherwise the node MUST rebroadcast the
   RREQ.

6.5. node generates a RREP as discussed
   further in section 9.4.

9.4. Generating Route Replies (RREPs) for IP Destinations

   If a node receives a route request for a destination, and has a
   fresh enough route to satisfy the request, the node generates a
   RREP message and unicasts it back to the node indicated by the
   Source IP Address field of the received RREQ. If the node is not the
   destination node, it copies over the destination sequence number from
   the route table entry.  If the generating node is the destination
   itself, it uses a destination sequence number at least equal to a
   sequence number generated after the last detected change in its
   neighbor set and at least equal to the destination sequence number in
   the RREQ. If the destination node has not detected any change in its
   set of neighbors since it last incremented its destination sequence
   number, it MAY use the same destination sequence number.

   As part of the process of generating the RREP, the generating node
   creates or updates an entry in its routing table for the Source
   IP Address, if necessary as described in section 6.4. 9.3.  The Source
   Sequence Number is put into the route entry, along with the Hop Count
   from the RREQ. The Lifetime for the route table entry is set to the
   current time plus ACTIVE_ROUTE_TIMEOUT milliseconds.

   If the generating node is not the destination node, then the
   generating node places its distance in hops from the destination
   in the Hop Count field.  If the generating node is the destination
   node, it places the value zero in the Hop Count field.  The Hop Count
   field is incremented by one at each hop as the RREP is forwarded to
   the source.  When the RREP reaches the source, the Hop Count will
   represent the distance, in hops, of the destination from the source.

   If the node is not the destination node, it calculates the Lifetime
   field of the RREP by subtracting the current time from the expiration
   time in its route table entry.  Otherwise, if the generating node
   is also the destination node, it copies the value MY_ROUTE_TIMEOUT
   into the Lifetime field of the RREP. Each node MAY make a separate
   determination about its value MY_ROUTE_TIMEOUT.

   If the generating node is not the node indicated by the Destination
   IP Address, then it puts the next hop towards the destination in the
   precursor list for the reverse path route entry.  In addition, the
   generating node puts the last hop node (from which it received the
   RREQ, as indicated by the source IP address field in the IP header)
   into the precursor list for the forward path towards the destination.

6.6. Generating

9.5. Forwarding Route Replies (RREPs) for Services

   If

   When a node hosts receives a service at RREP message, it first increments the protocol and port number Hop
   Count field in the RREP. If this node is the node indicated in the RREQ,
   Source IP Address field, it generates then creates a RREP and sends it back forward route entry to the requesting
   node.  The generating
   node copies the value MY_ROUTE_TIMEOUT into
   the Lifetime field of indicated by the RREP, and puts Destination IP Address field, using the value zero for node
   from which it received the Hop
   Count.  The destination sequence number is inserted just RREP as indicated
   in the previous section. next hop.  It can then begin
   using this route to send data packets to the destination.

   If a this node has a current resolution for is not the service type to an IP
   address, and if source node, it has a valid creates the forward route
   entry as described above.  It consults its route table entry for that IP address, it SHOULD
   generate a RREP and send it back to the requesting node.  The
   generating
   source node copies to determine the remaining value next hop for the lifetime of RREP packet, and then
   forwards the
   valid route into RREP towards the Lifetime field of source.  If the RREP, node later receives a
   RREP for the same source node, it only updates its forward route and puts
   forwards the value
   zero for RREP to the Hop Count.  The source node if the RREP contains either a
   greater destination sequence number is inserted
   just as indicated in number, or the previous section.

   In order to indicate same destination sequence
   number but smaller hopcount to the source of the RREQ destination.

   When any node generates or forwards a RREP, the particular service precursor list for which
   the RREQ was sent, corresponding destination is also updated by adding to it the generating
   next hop node includes a Service
   Resolution extension (see section 14.6).

   The mechanism for forwarding route replies to which the RREP is described in section
   8.3.

6.7. forwarded.

9.6. Hello Messages

   A node MAY offer connectivity information by broadcasting local
   Hello messages as follows.  Every HELLO_INTERVAL milliseconds, the
   node checks whether it has sent a broadcast (e.g., a RREQ) RREQ or an
   appropriate layer 2 message) within the last HELLO_INTERVAL. If it
   has not, it MAY generate a broadcast RREP with TTL = 1, called a
   Hello message, with the message fields set as follows:

      Destination IP Address
                  The node's IP address.

      Destination Sequence Number
                  The node's latest sequence number.

      Hop Count   0

      Lifetime    ALLOWED_HELLO_LOSS * HELLO_INTERVAL

   A node MAY determine connectivity by listening for packets from
   its set of neighbors.  If it receives no packets for more than
   ALLOWED_HELLO_LOSS * HELLO_INTERVAL milliseconds, the node SHOULD
   assume that the link to this neighbor is currently broken.  When this
   happens, the node SHOULD proceed as in Section 6.9.

6.8. 9.8.

9.7. Maintaining Local Connectivity

   Each forwarding node SHOULD keep track of its active next hops (i.e.,
   which next hops have been used to forward packets towards some
   destination within the last ACTIVE_ROUTE_TIMEOUT milliseconds).  This
   is done by updating the Lifetime field of a routing table entry used
   to forward data packets to current time plus ACTIVE_ROUTE_TIMEOUT
   milliseconds.  For purposes of efficiency, each node may try to learn
   which of these active next hops are really a neighbor in the neighborhood at the
   current time using one or more of the available link or network layer
   mechansisms,
   mechanisms, as described below.

    -  Any suitable link layer notification, such as those provided by
       IEEE 802.11, can be used to determine connectivity, each time
       a packet is transmitted to an active next hop.  For example,
       absence of a link layer ACK or failure to get a CTS after sending
       RTS, even after the maximum number of retransmission attempts,
       will indicate loss of the link to this active next hop.

    -  Passive acknowledgment can be used when the next hop is expected
       to forward the packet, by listening to the channel for a
       transmission attempt made by the next hop.  If transmission is
       not detected within NEXT_HOP_WAIT milliseconds or the next hop is
       not a forwarding node (and thus is never supposed to transmit the
       packet) one of the following methods should be used to determine
       connectivity.

        *  Receiving an ICMP ACK message from the next hop.  The ICMP
           ACK message SHOULD be sent to a forwarding node by a next hop
           which is also the destination as in the in the IP header of
           the packet.  This should be done only when this destination
           has not sent any packets to the concerned forwarding node
           within the last HELLO_INTERVAL milliseconds.

        *  A RREQ unicast to the next hop, asking for a route to the
           next hop.

        *  An ICMP Echo Request message unicast to the next hop.

   If a link to the next hop cannot be detected by any of these methods,
   the forwarding node SHOULD assume that the link is broken, and take
   corrective action by following the methods specified in Section 6.9.

6.9. Initiating Triggered 9.8.

9.8. Route Replies (Triggered RREPs) Error (RERR) Messages

   A node can send initiates a Triggered RREP (also called unsolcited RREP) RERR message if
   either it either detects a link breakage break for
   an active next hop in its routing table, or if it receives a RREP from a neighbor with an
   infinite metric for an active route.

   The Triggered RREP is sent to each node in the precursor list for the
   routing table entry for that destination.  The contents of the RREP
   fields are set as follows:

      Hop Count   255 (= infinity)

      Destination IP Address
                  The destination in the broken route

      Destination Sequence Number
                  One plus the destination sequence number recorded for
                  the route.

7. Multicast Route Activation (MACT) Message Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |P|G|U|      Reserved           |   Hopcount    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Multicast Group IP address                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Source IP address                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Source Sequence Number                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The format of the Multicast Route Activation message is illustrated
   above, and contains the following fields:

      Type        xx

      P           Prune flag; set when a node wishes to prune itself
                  from the tree, unset when the node is activating a
                  tree link.

      G           Group Leader flag; set by a multicast tree member that
                  fails to repair a multicast tree link breakage, and
                  indicates to RERR
   from a neighbor for an active route.

   If the group member receiving precursor list for the message
                  that it should become next hop is non-empty, the new multicast group leader.

      U           Update flag; set when a multicast tree member has
                  repaired node
   broadcasts a broken tree link RERR. The unreachable destinations included in the RERR
   message are the next hop, and is any additional destinations which are
   now a new distance
                  from unreachable due to the group leader.

      Reserved    Sent as 0; ignored on reception.

      Hop Count   The distance loss of the sending node from the multicast
                  group leader.  Used only when link.  The contents of the 'U' flag is set;
                  otherwise sent
   RERR fields are set as 0.

      Multicast Group IP Address
                  The IP address follows:

      Length   Number of unreachable destinations included in the Multicast Group for which a
                  route is supplied.

      Source RERR
               message.

      Unreachable Destination IP Address
               The IP address of destination which is now unreachable.  Note that
               there can be more than one such field, as indicated by
               the sending node.

      Source Sequence Number
                  The current sequence number Length field above.

   When a node receives a RERR packet, for route information
                  generated by each unreachable destination
   included in the source of packet, the route request.

   To prune itself from node determines whether the tree (i.e., inactivate its last link to source
   node forwarding the
   multicast tree), a multicast tree member sends a MACT with RERR packet is the 'P'
   flag = 1 to its next hop on used to reach that
   destination.  If so, the multicast tree.  A multicast tree
   member node copies the value in the Hop Count route
   table field into the Last Hop Count field, and marks the Hop Count
   for that has more than one next hop to destination as infinity.  It then checks its precursor list
   for each of the multicast tree SHOULD
   NOT try to prune itself from destinations.  If one or more of the multicast tree.

8. precursor lists
   are non-empty, it creates a RERR packet and includes as unreachable
   each destination with a non-empty precursor list.  It then broadcasts
   this RERR message.

10. Node Operation - Multicast

   This section describes the scenarios under which nodes generate
   RREQs, RREPs, and MACTs
   control messages for multicast communication, and how the fields in
   the messages are handled.

8.1.

10.1. Maintaining Multicast Tree Utilization Records

   For each multicast tree to which a node belongs, either because it
   is a member of the group or because it is a router for the multicast
   tree, the node also maintains a list of next hops -- i.e., those 1-hop
   neighbors that are likewise a part of the multicast tree.  This
   list of next hops is used for forwarding messages received for
   the multicast group.  A node will forward a multicast message to
   every such next hop, except that neighbor from which the message
   arrived.  If there are multiple next hops, the forwarding operation
   MAY be performed by broadcasting the multicast packet to the node's
   neighbors; only the neighbors that belong to the multicast tree will and
   have the sending node as a next hop and have not already seen that
   data packet continue to forward the multicast packet.

8.2.

10.2. Generating Multicast RREQs Route Requests

   A node sends a multicast RREQ either when it determines that it should be a
   part of a multicast group, and it is not already a member of that
   group, or when it has a message to send to the multicast group but
   does not have a route to that group.  If the node wishes to join the
   multicast group, it sets the `J' flag in the RREQ; otherwise, it
   leaves the flag unset.  The destination address of the RREQ is always
   set to the multicast group address.  If the node knows the group
   leader and has a route to it, the node will place places the group leader's
   address in the Multicast Group Leader extension (Section 14.2), 15.2), and will unicast
   unicasts the RREQ to the corresponding next hop for that destination.
   Otherwise, if the node does not have a route to the group leader, or
   if it does not know who the multicast group leader is, it will broadcast broadcasts
   the RREQ and will does not include the extension field.

   The process of waiting for a RREP to a RREQ with a multicast
   destination address is the same as that described in Section 6.3. 9.2.
   The node may resend the RREQ up to RREQ_RETRIES additional times if
   a RREP is not received.  If a RREQ was unicast to a group leader
   and a RREP is not received within RREP_WAIT_TIME milliseconds, the
   node
   will broadcast broadcasts subsequent RREQs for that multicast group across the
   network.  If a RREP is not received after RREQ_RETRIES additional
   requests, the node may assume that there are no other members of that
   particular group within the connected portion of the network.  If it
   wanted to join the multicast group, it MAY then become becomes the multicast
   group leader for that multicast group and initialize initializes the destination sequence
   number of the multicast group.  Otherwise, if it only wanted to send
   packets to that group without actually joining the group, it
   will drop drops
   the packets it had for that group.

   If

   When the node wishes to join or send a message to a multicast group,
   it first consults its Group Leader Table.  Based on the existence
   of an entry for the multicast group in this table, the node will then
   formulate
   formulates and send sends the RREQ as described at the beginning of this
   section.

8.3.

10.3. Forwarding Multicast Route Requests

   The operation of nodes forwarding RREQs for multicast is similar
   to that for the reception and forwarding of RREQs as described in
   Section 6.4, 9.3, with one exception.  If the RREQ is a join request, when
   the node it
   creates a reverse route to multicast group next hop entry for the Source IP Address, node from which it places
   received the information in its Multicast Route table. RREQ. The generation of the route reply (RREP) message
   is discussed in the following section.

8.4.

10.4. Generating Multicast Route Replies

   If a node receives a multicast join RREQ for a multicast group, and it is
   already a member of the multicast tree for that group, the node
   updates its Multicast Route Table and then generates a RREP message.
   It unicasts the RREP back to the node indicated by the Source IP
   Address field of the received RREQ. The RREP contains the current
   sequence number for the multicast group, the distance of the
   responding node from the multicast group leader, and the IP address of the
   group leader.  Additionally, it initializes the Hopcount field of
   the RREP to zero.  Further information about the multicast group
   leader is entered into the Multicast Group Information extension (see
   Section 14.3). 15.4).

   A node can only respond to a join RREQ if it is a member of the
   multicast tree.  If a node receives a multicast route request that
   is not a join message, it can reply if it has a current route to the
   multicast tree.  Otherwise it will continue forwarding the request.
   If a node receives a join route request RREQ for a multicast group and it is not
   already a member of the multicast tree for that group, it will
   rebroadcast the RREQ to its neighbors.

   In the event that a node receives a unicasted multicast route request
   that specifies its own IP address as the destination address (i.e.,
   the source node believes this destination node to be the multicast
   group leader), but the node is in fact not the group leader, it
   can simply ignore the RREQ. The source node will time out after
   RREP_WAIT_TIME milliseconds and will broadcast a new RREQ without the
   group leader address specified.

   Regardless of whether the multicast group leader or a multicast tree
   member generates the RREP, the RREP fields are set as follows:

      Hop Count    0

      Destination IP Address
                   The IP address of the node which supplies a route to
                   the multicast group.

      Destination Sequence Number
                   The destination sequence number of the node which
                   supplies a route to the current multicast group. group sequence number.

      Lifetime     The time for which nodes receiving the RREP consider
                   the route to be valid. valid (only used it the RREQ is not a
                   join request).

   The Multicast Group Information extension described in Section 14.3 15.4
   is also included.

8.5. included for join requests.  If the node generating the RREP
   is not on the multicast tree (because the RREQ was not a join RREQ),
   it places its distance from the multicast tree in the Hop Count
   field, instead of 0.

10.5. Forwarding Route Replies

   If an intermediate node receives a RREP in response to a RREQ that
   it has transmitted (or retransmitted on behalf of some other node),
   it increments the Hop Count and Multicast Group Hopcount fields and
   forwards the RREP along the path to the source of the RREQ.

   When the node receives more than one RREP for the same RREQ, it saves
   the route information with the greatest sequence number, and beyond
   that the lowest hop count; it discards all other RREPs.  This node
   forwards the first RREP towards the source of the RREQ, and then
   forwards later RREPs only if they have a greater sequence number or
   smaller metric.

8.6.

10.6. Route Deletion and Multicast Tree Pruning Activation

   When a node broadcasts a RREQ message, it is likely to receive more
   than one reply since any node in the multicast tree can respond.
   If multicast tree can respond.  If
   the RREQ was not a join request, then once the source node receives
   the first RREP, it may begin using this route to forward data
   packets.  On the other hand, if the RREQ was a join request, the RREP
   message traveling sets up route pointers as it travels back to the node which originated the request sets up source node.
   These route pointers, which pointers may eventually graft a branch onto the multicast
   tree.  If multiple branches to the same destination are created in
   such a manner, a loop will be formed.  Hence, in order to prevent
   the formation of any such loops, it is necessary to activate only
   one of the routes created by the RREP messages.  The RREP containing
   the largest destination sequence number is chosen to be the added
   branch to the multicast tree.  In the event that a node receives more
   than one RREP with the same (largest) sequence number, it selects the
   first one with the smallest hop count, i.e., the shortest distance to
   a member of the multicast tree.

   After waiting for RREP_WAIT_TIME milliseconds, the node must choose select the
   route it wishes to use as its link to the multicast tree.  This is
   accomplished by sending a Multicast Activation (MACT) message.  The
   Destination IP Address field of the MACT packet is set to the IP
   address of the multicast group.  The node unicasts this message to
   the selected next hop, effectively activating the route.  It then
   sets the Activated flag in the next hop Multicast Route Table entry
   associated with that node.  After receiving this message, the node's
   neighbor node
   to which the MACT was sent activates the route entry for the link in the
   its multicast route table, thereby finalizing the creation of the
   tree branch.  All neighbors not receiving this message time out and
   delete that node as a next hop for the multicast group in their route
   tables, having never activated the route entry for that next hop.

   Two scenarios exist for a neighboring node receiving the MACT
   message.  If this node was previously a member of the multicast
   tree, it does not propagate the MACT message any further.  However,
   if the next hop selected by the source node's MACT message was not
   previously a multicast tree member, it will have propagated the
   original RREQ further up the network in search of nodes which are
   tree members.  Thus it is possible that this node also received more
   than one RREP, as noted in section 8.5. 10.5.

   When the node receives a MACT announcing selecting it as the next hop, it sends
   unicasts its own MACT announcing to the node it has chosen as its next hop,
   and so on up the tree, until a node which was already a part of the
   multicast tree is reached.

   If a

10.7. Multicast Tree Pruning

   A multicast group member revokes can revoke its member status and wishes to
   remove itself from the multicast tree, at any time.
   However, it can do so only actually leave the multicast tree if it is not a
   multicast
   tree router for any other nodes in the multicast group (i.e., if it
   is a leaf node).  If this is a node wishing to leave the case, multicast group is
   a leaf node, it may unicast unicasts to its next hop on the tree a MACT message
   with the 'P' `P' flag set and with the Destination IP Address set to the
   IP address of the multicast group.  It then deletes the multicast
   group in order to prune itself information for that group from its Multicast Route Table.
   When its next hop receives this message, it deletes the sending
   node's information from its list of next hops for the multicast tree.  Similarly, if
   If the removal of the sending node
   receiving causes this message node to become a leaf
   node, and if this node is also not a member of the multicast group the multicast group,
   it may in turn prune itself by sending its own MACT message up the
   tree.

   When the multicast group leader wishes to leave the multicast group,
   it proceeds in a manner similar to the one just described.  If it
   is a leaf node, it may leave the group and unicast a prune message
   to its next hop.  The next hop will act in the manner described in
   Section 10.10, since the prune message is coming from its upstream
   neighbor.  Otherwise, if the group leader is not a leaf node, it may
   not prune itself from the tree.  It takes the actions described in
   Section 10.9, where it selects one of its next hops and
   does not have any other nodes routing through it, unicasts to
   it may send its own
   MACT message up the tree.

8.7. MACT with set `G' flag.

10.8. Repairing Link Breakages

   Branches of the multicast tree become invalid if they time out (the
   Lifetime associated with the route expires), or if a broken link breakage
   results in an infinite metric being associated with the route.  When
   a broken link breakage is detected between two nodes on the multicast tree,
   the node downstream of the break (i.e., the node which is further
   from the multicast group leader) is responsible for initiating
   the repair of the broken link.  In order to build repair the route back up,
   this tree, the
   downstream node broadcasts a RREQ with destination IP address set
   to the IP address of the multicast group leader and with the `J' flag
   set.  The destination sequence number of the RREQ is the last known
   sequence number of the multicast group.  The node also includes the
   Multicast Group Rebuild Extension.  The Multicast Group Hop Count
   field of this extension is set to the distance of the source node
   from the multicast group leader.  Only a  A node which has MUST have a hop count for to
   the multicast group leader less than or equal to the indicated value can
   in order to respond.  This hop count requirement is included to prevent prevents nodes on
   the same side of the break as the node initiating the repair from
   replying to the RREQ.

   The RREQ is broadcast using an expanding rings search.  Because of
   the high probability that other nearby nodes can be used to rebuild
   the route to the group leader, route, the original RREQ is broadcast with a TTL (time to live)
   field value equal to two more than the Multicast Group Hop Count.  In
   this way, the effects of the link breakage may be localized.  If no
   reply is received within RREP_WAIT_TIME milliseconds, all subsequent
   RREQs (up to RREQ_RETRIES additional attempts) will be broadcast
   across the entire network.  Any node that is a part of the multicast
   tree and that has a multicast group hop count to the multicast group leader smaller
   than that contained in the RREQ can return a RREP. If there is more
   than one RREP received at the originating node, route deletions occur
   as described in the previous section.

   At the end of the discovery period, the node selects its next hop
   and unicasts a MACT message to that node to activate the link,
   as described in Section 8.6. 10.7.  Additionally, since the node was
   repairing a tree breakage, break, it is likely that it is now a different
   distance from the group leader than it was before the break.  If this
   is the case, it must inform its DOWNSTREAM next hops of their new
   distance from the group leader.  It does this by sending its downstream next
   hops broadcasting a MACT
   message with the 'U' `U' flag set, and the Hopcount Hop Count field set to the
   node's new distance from the group leader.  This 'U' `U' flag indicates
   that multicast tree nodes should update their distance from the group
   leader.  If these nodes have downstream next hops, they in turn must
   send a MACT message with a set 'U' `U' flag to their next hops, and so
   on.  The Hopcount Hop Count field is incremented by one each time the packet
   is received.  When a node on the multicast tree receives the MACT
   message with the `U' flag set, in determines whether this packet
   arrived from its UPSTREAM neighbor.  If it did not, the node discards
   the packet.

   When a link break occurs, it is possible that the tree will be
   repaired through different intermediate nodes.  Hence, if the node
   UPSTREAM of the break is not a group member, and if the loss of that
   link causes it to become a leaf node, it sets a prune timer to wait
   for the link to be repaired.  This PRUNE_TIMEOUT should be larger
   than RREP_WAIT_TIMEOUT to give the link time to be repaired.  If,
   when this timer expires, the node has not received a MACT message
   selecting it to be a part of the repaired tree branch, it prunes
   itself from the tree by sending a MACT with set `P' flag to its next
   hop, as previously described.

10.9. Tree Partitions

   It is possible that after a link breaks, the tree cannot be repaired
   due to a network partition.  If the node attempting to repair a
   tree link breakage does not receive a response after RREQ_RETRIES
   attempts, it can be assumed that the network has become partitioned
   and the multicast tree cannot be repaired at this time.  In this
   situation, if the node which had initiated the route rebuilding was is a
   multicast group member, it will
   become becomes the new multicast group leader
   for its part of the multicast tree partition.  It broadcasts a Group
   Hello with the multicast
   group address extension field containing the corresponding for this multicast
   group IP address included. group.  The `U' flag in the Group Hello is
   set, indicating that there has been a change in the group leader
   information.  All nodes receiving this message update their Group
   Leader Table to indicate the new group leader information.  Nodes
   which are a part of the multicast tree also update the group leader
   information for that group in their Multicast Route Table to indicate
   the new group leader.

   On the other hand, if the node which had initiated the repair is not
   a multicast group member, there are two possibilities.  If it only
   has one next hop for the multicast tree, it will unicast prunes itself from the
   tree by unicasting a MACT message, with the 'P' `P' flag set, to its next hop, thereby indicating
   that it is pruning itself from the tree.
   hop.  The node receiving this message will note that it is coming the message came
   from its upstream link, i.e., from a node that is closer to the group
   leader than it is.  If the node receiving this message is a multicast
   group member, it will become the new group leader and will broadcast
   a Group Hello message as indicated above.  If  Otherwise, if it is not a
   multicast group member and it only has one other next hop link, it
   will similarly prune itself from the tree and this tree.  This process will continue continues
   until a multicast group member is reached.  On the

   The other hand, if possibility is that the node which initiated the rebuilding
   is not a group member and has more than one next hop for the tree, tree.
   In this case, it cannot prune itself, since doing so would partition
   the tree.  It instead chooses one of its next hops and sends unicasts a
   MACT with the 'G' `G' flag set. set to that node.  This flag indicates that
   the next group member to receive this message should become the
   new group leader.  It then changes the direction of that link to
   be UPSTREAM. If the node's next hop is a group member, this node will become
   becomes the group leader.  Otherwise, the node will unicast unicasts its own MACT
   message with the 'G' `G' flag set to one of its next hops, and so on until changes
   the direction of that link.  Once a group member is reached. reached, the new
   group leader is determined.

10.10. Reconnecting the Two Trees

   In the event that the a link break can not be repaired, the multicast
   tree will remain remains partitioned until the two parts of the network become
   connected once again.  A node from one partition of the network will know knows
   that it has come into contact with a node from the other partition
   of the network by noting the difference in the Group Hello message
   multicast group leader information.  The multicast group leader with
   the lower IP address initiates the tree repair.  For the purposes
   of this explanation, call this node GL1.  GL1 unicasts a RREQ with
   both the 'J' `J' and 'R' `R' flags set to the group leader of the other
   network partition (GL2), using the node from which it had received the
   Group Hello message from as the next hop.  This RREQ contains the current value
   of the partitions GL1's multicast group sequence number.  If any node that receives
   the RREQ is a member of GL2's multicast tree, it MUST forward the
   RREQ along its upstream link, i.e.  towards the group leader. GL2.  This prevents any
   loops from being formed after the repair.  Upon receiving the RREQ,
   GL2 takes the larger of its and the received multicast group sequence
   number, increments this value by one, and responds with a RREP. This
   is the group leader which will become the leader of the reconnected
   multicast tree.  The 'R' `R' flag of the RREP is set, indicating that
   this RREP is in response to a repair request.

   As the RREP is propagated back to GL1, nodes add the incoming and
   outgoing links to the Multicast Route Table next hop entries if
   these entries do not already exist.  The nodes also enable activate these
   entries, thereby adding the branch on to the multicast tree.  If a
   node that was previously a member of GL1's tree receives the RREP, it
   MUST forward the packet along its link to its previous group leader (G1).
   (GL1).  It then updates its group leader information to reflect GL2
   as the new group leader, changes the direction of the next hop link
   associated with GL1 to
   downstream DOWNSTREAM, and sets the direction of the
   link on which it received the RREP to upstream. UPSTREAM. When the GL1 receives
   the RREP, it updates its group leader information and sets the link
   from which it received the RREP as its upstream link.  The tree is
   now reconnected.  The next time GL2 broadcasts a Group Hello, it
   sets the `U' flag to indicate that there is a change in the group
   leader information and group members should update the corresponding
   information.  GL1 also notes this message and updates its tables
   to indicate that the other group leader is now the multicast group
   leader for the entire network.  Additionally, all  All network nodes update their Group Leader Table to
   reflect the new group leader information.

8.8. Initiating Triggered Route Replies

   A

10.11. Group Hello Messages

   If a node can trigger an unsolicited RREP if it sends a RREQ to join a multicast group (`J' flag set)
   and after RREQ_RETRIES times attempts does not receives a response. response, it
   then becomes the multicast group leader.  The node will then become initializes the new
   multicast group
   leader, sequence number and it will broadcast then broadcasts a RREP with infinity TTL (a Group Hello message) and with the multicast group IP Address / Sequence
   number extension information set
   message to reflect inform network nodes that it is now the group leader
   for the multicast group.  In addition, in order to  To ensure nodes maintain consistent and
   up-to-date information about who the multicast group leaders are,
   any node which is a group leader for a multicast group will broadcast group broadcasts
   such a Group Hello across the network every GROUP_HELLO_INTERVAL
   milliseconds.  The contents of the RREP GRPH fields (including the Multicast Group Information Extension) are set as follows:

      M Flag      0

      Hop Count   0

      Destination

      Group Leader IP Address
                  The IP Address of the node sending the Group Hello.

      Destination Sequence Number
                  The node's latest destination sequence number. group leader.

      Multicast Group IP Address
                  The IP Address of the Multicast Group for which the
                  node is the group leader.

      Multicast Group Sequence Number
                  One plus the last known sequence number of the
                  multicast group.

   Nodes receiving the Group Hello increment the Hop Count field and the
   Multicast Tree Hop Count Extension field by one
   before forwarding the message.

9.  When a node not on the multicast tree
   receives the GRPH message, it sets the M flag.  This indicates

11. Broadcast

   When a node wishes to generate a broadcast, it sends the broadcast
   packet to address 255.255.255.255.  AODV does not define any valid
   behavior for transmissions to any directed broadcast address.

   Every node maintains a list to keep track of which broadcast packets
   have already been received and retransmitted.  The list contains, for
   each distinct broadcast packet received, the source IP address and
   the IP ident value from the IP header of the broadcast packet.

   When a node receives a packet broadcast to address 255.255.255.255,
   it checks the source IP address and the IP ident value of the
   broadcast packet's IP header.  The node then checks to see whether
   the broadcast packet has already been received in the past, and thus
   whether it has already retransmitted the broadcast packet.  If there
   is no existing list entry containing the same IP source address and
   IP ident value, the node retransmits the broadcast packet.  If there
   is such a list entry with matching source IP address and IP ident
   field, the node silently discards the broadcast packet.

   List entries SHOULD be kept for at least BROADCAST_RECORD_TIME
   before the node expunges the record.  BROADCAST_RECORD_TIME
   is a configurable parameter, but it MUST be at least equal to
   RREP_WAIT_TIME.

10.

12. Quality of Service

   AODV currently provides some minimal controls to enable mobile nodes
   in an ad hoc network to specify, as part of a RREQ, certain Quality
   of Service parameters that a route to a destination must satisfy.

   In particular, a RREQ MAY include a Maximum Delay extension (see
   Section 14.4) 15.5) or a Minimum Bandwidth extension (see Section 14.5). 15.6).

   If, after establishment of such a route, any node along the path
   detects that the requested Quality of Service parameters can no
   longer be maintained, that node MUST originate a ICMP QOS_LOST
   message back to the node which had originally requested the now
   unavailable parameters.

11.

13. AODV and Aggregated Networks

   AODV has been designed for use by mobile nodes with IP addresses
   that are not necessarily related to each other, to create an ad hoc
   network.  However, in some cases a collection of mobile nodes MAY
   operate in a fixed relationship to each other and share a common
   subnet prefix, moving together within an area where an ad hoc network
   has formed.  Call such a collection of nodes a ``subnet''.  In this
   case, it is possible for a single node within the subnet to advertise
   reachability for all other nodes on the subnet, by responding with
   a RREP message to any RREQ message requesting a route to any node
   with the subnet routing prefix.  Call the single node the ``subnet
   router''.  In order for a subnet router to operate the AODV protocol
   for the whole subnet, it has to maintain a destination sequence
   number for the entire subnet.  In any such RREP message sent by the
   subnet router, the Prefix Length field of the RREP message MUST be
   set to the length of the subnet prefix.  Other nodes sharing the
   subnet prefix SHOULD NOT issue RREP messages.

12. messages, and SHOULD forward RREQ
   messages to the subnet leader.

14. Using AODV with Other Networks

   In some configurations, an ad hoc network may be able to provide
   connectivity between external routing domains that do not use
   AODV. If the points of contact to the other networks can act as
   subnet routers (see Section 11) 13) for any relevant networks within
   the external routing domains, then the ad hoc network can maintain
   connectivity to the external routing domains.  Indeed, the external
   routing networks can use the ad hoc network defined by AODV as a
   transit network.

   In order to provide this feature, a point of contact to an external
   network (call it an Infrastructure Router) has to act as the subnet
   router for every subnet of interest within the external network for
   which the Infrastructure Router can provide reachability.  This
   includes the need for maintaining a destination sequence number for
   that external subnet.

   If multiple Infrastructure Routers offer reachability to the same
   external subnet, those Infrastructure Routers have to cooperate (by
   means outside the scope of this specification) to provide consistent
   AODV semantics for ad hoc access to those subnets.

13. Service Location with AODV

   It is possible to use AODV's basic RREQ and RREP messages to locate
   services within an ad hoc network.  There are two extensions defined
   for this purpose:

    -  Service Discovery

    -  Service Resolution

   The basic operation of RREQ and RREP messages remains the same,
   except that additional functionality is defined to distinguish
   between the roles of IP path discovery and service location.  The
   time for which a path to an IP address remains valid is likely to
   be relatively short, and to depend upon the mobility factor of the
   mobile node.  Aging out such paths, to protect against using stale
   paths, is controlled by the timeout parameter ACTIVE_ROUTE_TIMEOUT.

   The association between a service and an IP address, on the other
   hand, is likely to remain valid for a much longer time.  The timeout
   parameter SERVICE_ASSOCIATION_TIMEOUT specifies how long a node may
   continue to associate a particular service with a particular IP
   address.  So, the external network for instance,
   which the first time that a mobile node needs
   access to a particular service, it will issue a RREQ with Infrastructure Router can provide reachability.  This
   includes the `S' bit
   set, and acquire need for maintaining a suitable path to the service.  Subsequent attempts
   to connect destination sequence number for
   that external subnet.

   If multiple Infrastructure Routers offer reachability to the same service may be carried out by issuing a RREQ
   with the `S' bit cleared, which then amount
   external subnet, those Infrastructure Routers have to cooperate (by
   means outside the regular operation scope of trying this specification) to establish a routing path provide consistent
   AODV semantics for ad hoc access to a known IP destination
   address.

14. those subnets.

15. Extensions

   RREQ, RREP,

   RREQ and MACT RREP messages have extensions defined in this version
   (and, possibly, future versions) of the protocol.  Extensions have the following
   format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |     type-specific data ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where:

      Type     xx

      Length   The length of the type-specific data, not including the
               Type and Length fields of the extension.

   Extensions with types between 128 and 255 may NOT be skipped.  The
   rules for extensions will be spelled out more fully, and conform with
   the rules for handling IPv6 options.

14.1.

15.1. Hello Interval Extension Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |  Hello Interval ...           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | ... Hello Interval, continued |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     xx

      Length   The length of the extension field.

      Hello Interval
               The number of milliseconds between successive
               transmissions of a Hello message.

   The Hello Interval extension MAY be appended to a RREP message with
   TTL == 1, to be used by a neighboring receiver in determine how long
   to wait for subsequent such RREP messages (i.e., Hello messages; see
   section 9.6).

15.2. Multicast Group Leader Extension Format

   This extension is appended to a RREQ by a node wishing to repair a
   multicast tree.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Type      |    Length    Length     | Multicast Group Leader IP ... |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |   ... Address (continued)     |  Hello Interval Previous Hop IP Address ...   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |   ... Hello Interval, continued (continued)             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     xx

      Length   The length of the extension field.

      Hello Interval extension.

      Multicast Group Leader IP Address
               The number of milliseconds between successive
               transmissions IP Address of a Hello message. the Multicast Group Leader.

      Previous Hop IP Address
               The Hello Interval extension MAY be appended IP Address of the node which previously received the
               RREQ. This field is used when the RREQ is unicast to
               the group leader when a RREP message with
   TTL == 1, node wishes to be used by join a neighboring receiver in determine how long multicast
               group.

   This extension is used when unicasting the RREQ to wait for subsequent such RREP messages (i.e., Hello messages; see
   section 6.7).

14.2. the group leader.
   Each node receiving the RREQ updates the Previous Hop IP Address
   field to reflect its address.

15.3. Multicast Group Leader Rebuild Extension Format

   This extension is appended to a RREQ by a node wishing to repair a
   multicast tree.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Type      |    Length     |   Multicast Group Hop Count   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              Multicast Group Leader IP Address                |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     xx

      Length   The length of the extension.

      Multicast Group Hop Count
               The distance in hops of the node sending the RREQ from
               the Multicast Group Leader.

      Multicast Group Leader IP Address
               The IP Address of the Multicast Group Leader.

   This extension is only used for rebuilding a multicast tree branch.
   In  It is
   used to ensure that case, a route only nodes as least as close to the Multicast Group Leader was known before
   the need for the repair was discovered, and the IP address of the group leader is placed in
   as indicated by the extension field.

14.3. Multicast Group Hop Count field respond to the
   request.

15.4. Multicast Group Information Extension Format

   The following extension is used to carry additional information for
   the RREP message (see Section 5) when sent to establish a route to a
   multicast destination.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |   Multicast Group Hop Count   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Multicast Group IP Address                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Multicast Group Sequence Number                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Multicast Group Leader IP Address / Multicast Tree Hop Count               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     xx

      Length   The length of the extension field.

      Multicast Group Hop Count
               The distance of the node from the Multicast Group Leader.

      Multicast Group IP Address
               The IP Address of the Multicast Group.

      Multicast Group Sequence Number
               The current sequence number of the Multicast Group.

      Multicast Group Leader IP Address
               The IP Address of the current Multicast Group Leader.

      Multicast Tree Hop Count
               The number of hops the packet has travelled off of the
               multicast tree. current Multicast Group Leader.

   This extension is included when responding to a multicast group RREQ.
   In this case, the last field is used as the Multicast Group Leader IP
   Address.  The extension is also used by RREQ to join a
   multicast group leader when
   sending a Group Hello. group.  The extension fields indicate which group the node is responding to the RREQ places its distance
   from the group leader of and the current sequence number for that
   group.  For a Group Hello the last field is in the Multicast Tree Group Hop
   Count.  This field is incremented once each time it is received by a
   non-tree node.

14.4. Count field.

15.5. Maximum Delay Extension Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |          Max Delay            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type         xx

      Length       The length of the extension field.

      Max Delay    The number of seconds allowed for a transmission from
                   the source to the destination.

   The Maximum Delay Extension can be appended to a RREQ by a requesting
   node in order to place a maximum bound on the acceptable time
   delay experienced on any acceptable path from the source to the
   destination.

   Before forwarding the RREQ, an intermediate node MUST compare its
   NODE_TRAVERSAL_TIME to the (remaining) Max Delay indicated in the
   Maximum Delay Extension.  If the Max Delay is less, the node MUST
   discard the RREQ and not process it any further.  Otherwise, the
   node subtracts NODE_TRAVERSAL_TIME from the Max Delay value in
   the extension and continues processing the RREQ as specified in
   Section 6.4.

14.5. 9.3.

15.6. Minimum Bandwidth Extension Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |    Minimum Bandwidth ...      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  ...  Minimum Bandwidth       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type         xx

      Length       The length of the extension field.

      Minimum Bandwidth
                   The amount of bandwidth (in kilobits/sec) needed
                   for acceptable transmission from the source to the
                   destination.

   The Minimum Bandwidth Extension can be appended to a RREQ by a
   requesting node in order to specify the minimal amount of bandwidth
   that must be made available along acceptable path from the source to
   the destination.

   Before forwarding the RREQ, an intermediate node MUST compare its
   available link capacity to the Minimum Bandwidth indicated in the
   extension.  If the requested amount of bandwidth is not available,
   the node MUST discard the RREQ and not process it any further.
   Otherwise, the node continues processing the RREQ as specified in
   Section 6.4.

14.6. Service Resolution Extension Format

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |            Protocol           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Port              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type         xx

      Length       The length of the extension field.

      Protocol
                   Either 6, to indicate TCP, or 17, to indicate UDP.
                   Support for other protocols are remains undefined.

      Port         The port number at which service applications await
                   application protocol messages sent over TCP or UDP,
                   as indicated by the ``Protocol'' field.

   The Service Discoveery Extension Format can be appended to a RREQ by
   a requesting node in order to discover the IP address, and a route to
   that address, at which a service application is available.

   Note that a service is likely to remain in operation at a particular
   IP address for a time (SERVICE_RESIDENCE_TIME) that is much longer
   than the amount of time that the route to that IP address will remain
   available.

15. 9.3.

16. Configuration Parameters

   This section gives default values for some important values
   associated with AODV protocol operations.  A particular mobile node
   may wish to change certain of the parameters, in particular the
   NET_DIAMETER, MY_ROUTE_TIMEOUT, ALLOWED_HELLO_LOSS, RREQ_RETRIES,
   and possibly the HELLO_INTERVAL. In the latter case, the node should
   advertise the HELLO_INTERVAL in its Hello messages, by appending
   a Hello Interval Extension to the RREP message.  Choice of these
   parameters may affect the performance of the protocol.

      Parameter Name           Value
      ----------------------   -----
      ACTIVE_ROUTE_TIMEOUT     3,000 Milliseconds
      ALLOWED_HELLO_LOSS       2
      BAD_LINK_LIFETIME        2 * RREP_WAIT_TIME
      BCAST_ID_SAVE            30,000 Milliseconds
      BROADCAST_RECORD_TIME    RREP_WAIT_TIME
      GROUP_HELLO_INTERVAL     5,000 Milliseconds
      HELLO_INTERVAL           1,000 Millisecond
      MTREE_BUILD              2 * REV_ROUTE_LIFE
      MY_ROUTE_TIMEOUT         2 * ACTIVE_ROUTE_TIMEOUT
      NET_DIAMETER             35
      NEXT_HOP_WAIT            NODE_TRAVERSAL_TIME + 10
      NODE_TRAVERSAL_TIME      40 Milliseconds
      PRUNE_TIMEOUT            ACTIVE_ROUTE_TIMEOUT
      REV_ROUTE_LIFE           RREP_WAIT_TIME
      RREP_WAIT_TIME           3 * NODE_TRAVERSAL_TIME * NET_DIAMETER / 2
      RREQ_RETRIES             2
      SERVICE_ADDR_TIMEOUT     300,000
      TTL_START                1
      TTL_INCREMENT            2
      TTL_THRESHOLD            7
   NET_DIAMETER measures the maximum possible number of hops between
   two nodes in the network.  NODE_TRAVERSAL_TIME is a conservative
   estimate of the average one hop traversal time for packets and should
   include queueing delays, interrupt processing times and tranfer transfer
   times.  ACTIVE_ROUTE_TIMEOUT SHOULD be set to a longer value (at
   least 10,000 milliseconds) if link-layer indications are used to
   detect link breakages such as in IEEE 802.11 [3] standard.  TTL_START
   should be set to at least 2 if hello Hello messages are used for local
   connectivity information.  Performance of the AODV protocol is
   sensitive to the chosen values of these constants, which often depend
   on the characteristics of the underlying link layer protocol, radio
   technologies etc.

16.

17. Security Considerations

   Currently, AODV does not specify any special security measures.
   Route protocols, however, are prime targets for impersonation
   attacks, and must be protected by use of authentication techniques
   involving generation of unforgeable and cryptographically strong
   message digests or digital signatures.  It is expected that, in
   environments where security is an issue, that IPSec authentication
   headers will be deployed along with the necessary key management to
   distribute keys to the members of the ad hoc network using AODV.

References

   [1] S. Bradner.  Key Words words for Use use in RFCs to Indicate Requirement
       Levels.  RFC 2119, March 1997.

   [2] Charles E. Perkins.  Terminology for Ad-Hoc Networking.
       draft-ietf-manet-terms-00.txt, November 1997.  (work in
       progress).

   [3] IEEE Standards Department.  Wireless LAN Medium Access Control
       (MAC) and Physical Layer (PHY) Specifications.  IEEE Standard
       802.11--1997, 1997.

Author's Address Addresses

   Questions about this memo can be directed to:

      Charles E. Perkins
      Networking and Security
      Communications Systems Laboratory
      Nokia Research Center
      Sun Microsystems Laboratories
      901 San Antonio Rd.
      Palo Alto,
      313 FairChild Drive
      Mountain View, CA 94303
      USA
      +1 650 786 6464 625 2986
      +1 650 786 6445 691 2170 (fax)
      cperkins@eng.sun.com
      charliep@iprg.nokia.com

      Elizabeth M. Royer
      Dept. of Electrical and Computer Engineering
      University of California, Santa Barbara
      Santa Barbara, CA 93106
      +1 805 893 7788
      +1 805 893 3262 (fax)
      eroyer@alpha.ece.ucsb.edu

      Samir R. Das
      Division of Computer Science
      University of Texas at San Antonio
      San Antonio, TX 78249
      +1 210-458-5537 210 458 5537
      +1 210-458-4437 210 458 4437 (fax)
      samir@cs.utsa.edu