Network Working Group D. Katz Internet Draft Juniper Networks D. Ward Cisco Systems Expires:
January,August, 2005 February, 2005 July, 2004BFD for IPv4 and IPv6 (Single Hop) draft-ietf-bfd-v4v6-1hop-00.txtdraft-ietf-bfd-v4v6-1hop-01.txt Status of this Memo This document is an Internet-DraftBy submitting this Internet-Draft, I certify that any applicable patent or other IPR claims of which I am aware have been disclosed, or will be disclosed, and isany of which I become aware will be disclosed, in full conformanceaccordance with all provisions of Section 10 of RFC2026.RFC 3668. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txthttp://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.http://www.ietf.org/shadow.html Copyright Notice Copyright (C) The Internet Society (2004).(2005). All Rights Reserved. Abstract This document describes the use of the Bidirectional Forwarding Detection protocol over IPv4 and IPv6 for single IP hops. It further describes the use of BFD with OSPFv2, OSPFv3, and IS-IS. Comments on this draft should be directed to firstname.lastname@example.org. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [KEYWORDS]. 1. Introduction One very desirable application for BFD [BFD] is to track IPv4 and IPv6 connectivity between directly-connected systems. This could be used to supplant the detection mechanisms in IS-IS and OSPF, or to monitor router-host connectivity, among other applications. This document describes the particulars necessary to use BFD in this environment, and describes how BFD can be used in conjunction OSPFv2 [OSPFv2], OSPFv3 [OSPFv3], and IS-IS [ISIS]. 2. Applications and Limitations This application of BFD can be used by any pair of systems communicating via IPv4 and/or IPv6 across a single IP hop that can be associated with an incoming interface. This includes, but is not limited to, physical media, virtual circuits, and tunnels. Each BFD session between a pair of systems MUST traverse a separate path in both directions. If BFD is to be used in conjunction with both IPv4 and IPv6 on a particular link, a separate BFD session MUST be established for each protocol (and thus encapsulated by that protocol) over that link. 3. Initialization and Demultiplexing In this application, there will be only a single BFD session between two systems over a given interface (logical or physical) for a particular protocol. The BFD session must be bound to this interface. As such, both sides of a session MUST take the "Active" role (sending initial BFD Control packets with a zero value of Your Discriminator) and any BFD packet from the remote machine with a zero value of Your Discriminator MUST be associated with the session bound to the remote system, interface, and protocol. 4. Encapsulation 4.1. BFD for IPv4 In the case of IPv4, BFD Control packets MUST be transmitted in UDP packets with destination port 3784, within an IPv4 packet. The source port MUST be in the range 49152 through 65535. The same UDP source port number MUST be used for all BFD Control packets associated with a particular session. The source port number SHOULD be unique among all BFD sessions on the system. If more than 16384 BFD sessions are simultaneously active, UDP source port numbers MAY be reused on multiple sessions, but the number of distinct uses of the same UDP source port number SHOULD be minimized. An implementation MAY use the UDP port source number to aid in demultiplexing incoming BFD Control packets, but ultimately the mechanisms in [BFD] MUST be used to demultiplex incoming packets to the proper session. BFD Echo packets MUST be transmitted in UDP packets with destination UDP port 3785 in an IPv4 packet. The setting of the UDP source port is outside the scope of this specification. The destination address MUST be chosen in such a way as to cause the remote system to forward the packet back to the local system. The source address MUST be chosen in such a way as to preclude the remote system from generating ICMP Redirect messages (in particular, the source address MUST NOT be part of the subnet bound to the interface over which the BFD Echo packet is being transmitted.) 4.2. BFD for IPv6 In the case of IPv6, BFD Control packets MUST be transmitted in UDP packets with destination port 3784, within an IPv6 packet. The source port MUST be in the range 49152 through 65535. The same UDP source port number MUST be used for all BFD Control packets associated with a particular session. The source port number SHOULD be unique among all BFD sessions on the system. If more than 16384 BFD sessions are simultaneously active, UDP source port numbers MAY be reused on multiple sessions, but the number of distinct uses of the same UDP source port number SHOULD be minimized. An implementation MAY use the UDP port source number to aid in demultiplexing incoming BFD Control packets, but ultimately the mechanisms in [BFD] MUST be used to demultiplex incoming packets to the proper session. BFD Echo packets MUST be transmitted in UDP packets with destination UDP port 3785 in an IPv6 packet. The setting of the UDP source port is outside the scope of this specification. The source and destination addresses MUST both be associated with the local system. The destination address MUST be chosen in such a way as to cause the remote system to forward the packet back to the local system. 5. TTL/Hop Count Issues AllIf BFD authentication is not in use, all BFD Control packets for sessions operating according to this specification MUST be sent with a TTL or Hop Count value of 255. All received BFD Control packets that are demultiplexed to sessions operating according to this specification MUST be discarded if the received TTL or Hop Count is not equal to 255. A discussion of this mechanism can be found in [GTSM]. If BFD authentication is in use, any value of TTL/Hop Count MAY be used in transmitted packets, and received packets MUST NOT be discarded based on the received TTL/Hop Count. 6. Addressing Issues On a subnetted network, BFD Control packets MUST be transmitted with source and destination addresses that are part of the subnet (addressed from and to interfaces on the subnet.) On an addressed but unsubnetted point-to-point link, BFD Control packets MUST be transmitted with source and destination addresses that match the addresses configured on that link. On an unnumbered point-to-point link, the source address of a BFD Control packet MUST NOT be used to identify the session. This means that the initial BFD packet MUST be accepted with any source address, and that subsequent BFD packets MUST be demultiplexed solely by the My Discriminator field (as is always the case.) This allows the source address to change if necessary. Note that the TTL/Hop Count check described in section 5 precludes the BFD packets from having come from any source other than the immediate neighbor. 7. BFD for use with OSPFv2, OSPFv3, and IS-IS The two versions of OSPF, as well as IS-IS, all suffer from an architectural limitation, namely that their Hello protocols are limited in the granularity of failure their detection times. In particular, OSPF has a minimum detection time of two seconds, and IS- IS has a minimum detection time of one second. BFD MAY be used to achieve arbitrarily small detection times for these protocols by supplanting the Hello protocols used in each case. It should be noted that the purpose of using BFD in this context is not to replace the adjacency timeout mechanism, nor is it to demonstrate that the network is fully functional for the use of the routing protocol, but is simply to advise the routing protocol that there are problems forwarding the data protocol for which the routing protocol is calculating routes. 7.1. Session Establishment The mechanism by which a BFD session is established in this environment is outside the scope of this specification. An obvious choice would be to use the discovery mechanism inherent in the Hello protocols in OSPF and IS-IS to bootstrap the establishment of a BFD session. Any BFD sessions established to support OSPF and IS-IS across a single IP hop MUST operate in accordance with the rest of this document. If multiple routing protocols wish to establish BFD sessions with the same remote system for the same data protocol, all MUST share a single BFD session. 7.2. Session Parameters The setting of the various timing parameters and modes in this application are outside the scope of this specification. Note that all protocols sharing a session will operate using the same parameters. The mechanism for choosing the parameters among those desired by the various protocols are outside the scope of this specification. 7.3. Interactions with OSPF and IS-IS without Graceful Restart When a BFD session transitions from Up to Failing, action SHOULD be taken in the routing protocol to signal the lack of connectivity for the data protocol (IPv4 or IPv6) over which BFD is running. If only one data protocol is being advertised in the routing protocol Hello, or if multiple protocols are being advertised but the protocols must share a common topology, a Hello protocol timeout SHOULD be emulated for the associated OSPF neighbors and/or IS-IS adjacencies. If multiple data protocols are advertised in the routing protocol Hello, and the routing protocol supports different topologies for each data protocol, the failing data protocol SHOULD no longer be advertised in Hello packets in order to signal a lack of connectivity for that protocol. IfNote that it is possible in some failure scenarios for the network to be in a state such that the IGP comes up, but the BFD session cannot be established, and, more particularly, data cannot be forwarded. To avoid this situation, it would be beneficial to not allow the IGP to establish a neighbor/adjacency. However, this would preclude the operation of the IGP in an environment in which not all systems support BFD. Therefore, if a BFD session never reachesis not in Up state (possibly because the remote system does not support BFD), this MUST NOTit is OPTIONAL to preclude the establishment of an OSPF neighbor or an IS-IS adjacency. The choice of whether to do so SHOULD be controlled by means outside the scope of this specification, such as configuration or other mechanisms. 7.4. Interactions with OSPF and IS-IS with Graceful Restart The Graceful Restart functions in OSPF [OSPF-GRACE] and IS-IS [ISIS- GRACE] are predicated on the existence of a separate forwarding plane that does not necessarily share fate with the control plane in which the routing protocols operate. In particular, the assumption is that the forwarding plane can continue to function while the protocols restart and sort things out. BFD implementations announce via the Control Plane Independent (C) bit whether or not BFD shares fate with the control plane. This information is used to determine the actions to be taken in conjunction with Graceful Restart. If BFD does not share its fate with the control plane on either system, it can be used to determine whether Graceful Restart is NOT viable (the forwarding plane is not operating.) In this situation, if a BFD session fails while graceful restart is taking place, and BFD is independent of the control plane on the local system, and the remote system has been transmitting BFD Control packets with the C bit set, the graceful restart SHOULD be aborted and the topology change made visible to the network as outlined in section 7.3. If BFD shares its fate with the control plane on either system (either the local system shares fate with the control plane, or the remote system is transmitting BFD packets with the C bit set to zero), it is not useful during graceful restart, as the BFD session is likely to fail regardless of the state of the forwarding plane. The action to take in this case depends on the capabilities of the IGP. 7.4.1. OSPF Graceful Restart With Control Plane Fate Sharing OSPF has a "planned" restart mechanism, in which the restarting system notifies its neighbors that it is about to perform a restart. In this situation, if a BFD session fails while graceful restart is taking place (or ifthe BFD session failure triggersneighbor is performing a graceful restart event),restart, the graceful restart SHOULD be allowed to complete and the topology change should not be made visible to the network as outlined in section 7.3. 7.5. OSPF Virtual Links If it is desired to use BFD for failure detction of OSPF Virtual Links,For unplanned restarts (in which the mechanismneighbor has not notified the local system of its intention to restart), the OSPF Graceful Restart specification allows a Graceful Restart to take place if the system restarts prior to the expiration of the OSPF neighbor relationship. In this case, the BFD Detection Time is likely to expire prior to the restart, and the neighbor relationship SHOULD be torn down. In the unlikely event that the system restarts quickly enough, and the system chooses to attempt a Graceful Restart, the graceful restart SHOULD be allowed to complete and the topology change should not be made visible to the network as outlined in section 7.3. 7.4.2. ISIS Graceful Restart With Control Plane Fate Sharing ISIS Graceful Restart does not signal a "planned" restart; its mechanism does not begin until after the system has restarted. If the BFD session expires prior to the restart of the system, there is no way for the neighbors to know that a Graceful Restart will take place. If a planned restart is about to place, the restarting system MAY change the BFD timing parameters on a temporary basis in such a way as to make the Detection Time greater than or equal to the ISIS adjacency timeout. This will provide the restarting system the same opportunity to enter Graceful Restart as it would have without BFD. In this case, the restarted system SHOULD avoid sending any BFD Control packets until there is a high likelihood that its neighbors know it is performing a Graceful Restart, since the neighbors will tear down their BFD sessions when those sessions restart. In any case, if a BFD session fails while the neighbor is known to be performing a Graceful Restart, the Graceful Restart SHOULD be allowed to complete and the topology change should not be made visible to the network as outlined in section 7.3. If the BFD session fails, and it is not known whether the neighbor is performing a Graceful Restart, the BFD session failure SHOULD be made visible to the network as outlined in section 7.3. 7.5. OSPF Virtual Links If it is desired to use BFD for failure detction of OSPF Virtual Links, the mechanism described in [BFD-MULTI] MUST be used, since OSPF Virtual Links may traverse an arbitrary number of hops. BFD Authentication SHOULD be used and is strongly encouraged. 8. BFD for use with Tunnels A number of mechanisms are available to tunnel IPv4 and IPv6 over arbitrary topologies. If the tunnel mechanism does not decrement the TTL or hop count of the network protocol carried within, the mechanism described in this document may be used to provide liveness detection for the tunnel. The BFD Authentication mechanism SHOULD be used and is strongly encouraged. Normative References [BFD] Katz, D., and Ward, D., "Bidirectional Forwarding Detection", draft-ietf-bfd-base-00.txt, July, 2004.draft-ietf-bfd-base-01.txt, February, 2005. [BFD-MULTI] Katz, D., and Ward, D., "BFD for Multihop Paths", draft- ietf-bfd-multihop-00.txt, July, 2004.ietf-bfd-multihop-01.txt, February, 2005. [GTSM] Gill, V., et al, "The Generalized TTL Security Mechanism (GTSM)", RFC 3682, February 2004. [ISIS] Callon, R., "Use of OSI IS-IS for routing in TCP/IP and dual environments", RFC 1195, December 1990. [ISIS-GRACE] Shand, M., and Ginsberg, L., "Restart signaling for IS- IS", draft-ietf-isis-restart-05.txt, JanuaryRFC 3847, July 2004. [KEYWORD] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", RFC 2119, March 1997. [OSPFv2] Moy, J., "OSPF Version 2", RFC 2328, April 1998. [OSPFv3] Coltun, R., et al, "OSPF for IPv6", RFC 2740, December 1999. [OSPF-GRACE] Moy, J., et al, "Graceful OSPF Restart", RFC 3623, November 2003. Security Considerations In this application, the use of TTL=255 on transmit and receive is viewed as supplying equivalent security characteristics to other protocols used in the infrastructure, as it is not trivially spoofable. The security implications of this mechanism are further discussed in the GTSM specification. The security implications of the use of BFD Authentication are discussed in the base BFD specification. Authors' Addresses Dave Katz Juniper Networks 1194 N. Mathilda Ave. Sunnyvale, California 94089-1206 USA Phone: +1-408-745-2000 Email: email@example.com Dave Ward Cisco Systems 170 W. Tasman Dr. San Jose, CA 95134 USA Phone: +1-408-526-4000 Email: firstname.lastname@example.org Changes from the previous draft The only significant changes to this version are the additionoption of language describing tunnelsnot using the TTL=255 hack when authentication is in use, the option of suppressing ISIS and OSPF virtual links.neighbors while the BFD session is down, and further explication of the interactions with Graceful Restart. All other changes are editorial in nature. Full Copyright Notice Copyright (C) The Internet Society (2004). All Rights Reserved.(2005). This document and translations of it may be copied and furnishedis subject to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided thatthe above copyright noticerights, licenses and this paragraph are included on all such copies and derivative works. However, this document itself may not be modifiedrestrictions contained in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations,BCP 78, and except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked byset forth therein, the Internet Society or its successors or assigns.authors retain all their rights. This document and the information contained herein isare provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMSDISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE."PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. This document expires in August, 2005.