--- 1/draft-ietf-6man-enhanced-dad-09.txt	2014-11-13 12:14:52.238591425 -0800
+++ 2/draft-ietf-6man-enhanced-dad-10.txt	2014-11-13 12:14:52.266592108 -0800
@@ -4,21 +4,21 @@
 Updates: 4862, 4861, 3971 (if approved)                        W. Beebee
 Intended status: Standards Track                            C. Pignataro
 Expires: May 17, 2015                                Cisco Systems, Inc.
                                                                  E. Dart
                                    Lawrence Berkeley National Laboratory
                                                                W. George
                                                        Time Warner Cable
                                                        November 13, 2014
 
                   Enhanced Duplicate Address Detection
-                    draft-ietf-6man-enhanced-dad-09
+                    draft-ietf-6man-enhanced-dad-10
 
 Abstract
 
    IPv6 Loopback Suppression and Duplicate Address Detection (DAD) are
    discussed in Appendix A of RFC4862.  That specification mentions a
    hardware-assisted mechanism to detect looped back DAD messages.  If
    hardware cannot suppress looped back DAD messages, a software
    solution is required.  Several service provider communities have
    expressed a need for automated detection of looped backed Neighbor
    Discovery (ND) messages used by DAD.  This document includes
@@ -163,21 +163,21 @@
    o  Looped back message - also referred to as a reflected message.
       The message sent by the sender is received by the sender due to
       the network or an Upper Layer Protocol on the sender looping the
       message back.
 
    o  Loopback - A function in which the router's layer-3 interface (or
       the circuit to which the router's interface is connected) is
       looped back or connected to itself.  Loopback causes packets sent
       by the interface to be received by the interface and results in
       interface unavailability for regular data traffic forwarding.  See
-      more details in section 9.1 of [RFC2178].  The Loopback function
+      more details in section 9.1 of [RFC2328].  The Loopback function
       is commonly used in an interface context to gain information on
       the quality of the interface, by employing mechanisms such as
       ICMPv6 pings and bit-error tests.  In a circuit context, this
       function is used in wide area environments including optical Dense
       Wave Division Multiplexing (DWDM) and SONET/SDH for fault
       isolation (e.g. by placing a loopback at different geographic
       locations along the path of a wide area circuit to help locate a
       circuit fault).  The Loopback function may be employed locally or
       remotely.
 
@@ -468,21 +468,21 @@
    describing the use cases.
 
 9.  Normative References
 
    [RFC1661]  Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51,
               RFC 1661, July 1994.
 
    [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.
 
-   [RFC2178]  Moy, J., "OSPF Version 2", RFC 2178, July 1997.
+   [RFC2328]  Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
 
    [RFC3971]  Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
               Neighbor Discovery (SEND)", RFC 3971, March 2005.
 
    [RFC4429]  Moore, N., "Optimistic Duplicate Address Detection (DAD)
               for IPv6", RFC 4429, April 2006.
 
    [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
               "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
               September 2007.